I like a number of folks noticed that the Rialta body sits quite low to the ground. In fact, the Rialta I bought had significant scrapes under the drains. I checked with a number of businesses who do spring and suspension work on vehicles and they told me that it would be OK to raise the body 2" (but they suggested no more than that). I still can raise the body even more by putting more pressure in the air springs but the way the Rialta sits now I can leave the pressure in the air springs at around 40 psi and the ride is good and the clearance is good as well.
The following picture is the top of the pin (bolt) with the nut removed that goes through the springs from the axle. My understanding is that on every other vehicle in the world (a bit of an exaggeration) the pin is used to hold the springs in alignment and you usually never have to take the nut off when removing an axle. This is not true for the Rialta.
Notice the bolt in this picture is actually part of the axle!!!!
And you can see here that when the Rialta axle was put together at the factory they actually put the bolt through the spring support, welded it to the spring support, then welded the support to the axle tube. There is no way to remove this bolt.
We will get back to this topic shortly, but for now, the way I got the parts for this job was at a local truck spring shop. I told the owner what I wanted to do and he went through a pile of parts taken off trucks and found 2 2" spacers that would fit on top of my axle. He made the U bolts right in front of me with a large press and gave me the nuts and lock washers as shown in the picture. Notice the curved part on the spacers. This he told me was called a bump stock and its purpose is to stop the vehicle body if it is loaded heavily and you hit a bump from going any lower toward the axle. There is a rubber thing on our Rialta's on the body above the springs that is supposed to hit the bump stock if too much bounce occurs.
A - 2" spacers
B - Part from existing spring setup
C - Part from existing spring setup
D - Pins that will now go through the springs (explained shortly)
E - Piece of 1/8" steel I cut and drilled a hole through for the nub on the spacer to fit into (explained shortly)
This is a blurry view of the alignment hole in the springs.
A - piece if 1/8 steel
B - nub on the bottom side of the spacer. (The spacer is upside down in this picture).
C - The hole I drilled in the steel. When you get the spring pins (which should be the same diameter as the bolt that was welded to the axle there will be a round head on it that will fit in this hole (once again this will be clearer with the later pictures)
Here the steel is placed over the spacer nub and am making sure the nub does not stick out above the steel.
Okay, so now all will become clearer. I cut the bolt off of the axle.
And now lay the steel plate over the axle where the bolt was, centering it a accurately as possible over the the outline of the bolt hole. You want this perfectly centered because this is the way that the rear axle is made to be square with the Rialta body. The spring pins head should fit snugly into the hole in the steel.
Things should start to make more sense now. The plate is centered and welded to the axle support.
The following photos just show that if you take the axle off the vehicle you have to disconnect the brake lines. All my fittings were frozen and I needed heat to remove them. Since everything was apart I decided to make new metal brake lines on the axle and had a shop make the flexible lines that run from the body to the axle. I added a few inches to the length to account for the body being higher than the axle than it previously was
Here is the photo that shows it all together. Unfortunately I did not take a picture of everything but I will explain the steps to put it all together. First the pin that is a replacement for what used to be the bolt is put through the springs and bolted in with a nut on top. This photo unfortunately doesn't show the nut on top but it is there just hidden behind one of those big U-bolts. The head of the pin goes into the hole on the spacer and the spacer nub goes into the steel plate welded to the axle. It is all pulled tight by the 2 U-bolts.
Notice the photo with the bump stop side of the spacer and the little rubber block above it on the body of the RV.
These are the new Bilstein shocks that I used because of the extra lift. I got these with the help of the owner of a 4x4 shop that modifies trucks for off-road use. He made sure that the length when fully extended and compressed was the right range.
In closing, one might ask why did I make the steel spacer instead of just drilling out the bolt I cut off. The reason was because I was afraid that I would drill the hole a little off center and then the rear axle would not be at perfect right angle to the body. When I had the Rialta aligned after the modifications the rear axle alignment was within specs (Yay!). One final note, the emergency brake cables did not have to be extended but the brackets that they were attached to did not work anymore so I used heavy duty twist ties to hold them in place