Rialta Manual Swap — Building a Stiffer Pendulum Mount Bushing

Replacing a too-soft new rubber bushing with a cast 90A polyurethane bushing (PMC-790) to reduce engine/transmission rock.

Executive summary

After converting my Rialta (Eurovan-based) from an automatic to a manual transmission, I noticed that the drivetrain had noticeable fore–aft rocking during quick throttle lift and sometimes when I didn't shift smoothly. This wasn't severe and I was compensating by being very careful to smoothly shift and to not let my foot off the gas pedal rapidly. Thinking that the pendulum mount bushing was old I replaced it with a new one but it proved too compliant for the new load profile of the manual transmission and the heavy Rialta. The fix was to rebuild the bushing using a very hard polyurethane (Shore 90A, Smooth-On PMC-790), eliminating the large internal voids and replacing “mushy” rubber compliance with a stiffer, more controlled mount. The result was a substantial reduction in drivetrain movement, and shifting feel improved materially, with no more rocking when lifting my foot off the gas pedal rapidly.

Background: what changed and why it started rocking

The pendulum mount (often called the dogbone mount) primarily controls engine/transmission rotation and fore–aft motion under torque changes. With the automatic transmission, the torque converter and automatic shift strategy tend to smooth and phase in torque changes. After the manual swap, torque transitions became more abrupt:

Net: the mount system started behaving like a spring with insufficient damping and too much compliance, so you can feel it as a “rock” during throttle and shift transients.

Problem with the new rubber bushing

Even though the bushing was new, its design and material properties were still “automatic-friendly”: soft rubber plus large voids. Those voids and the rubber’s compliance allow large deflection under sudden torque transitions.

Pendulum mount bushing with four voids in the rubber
Photo 1: The original-style rubber bushing includes multiple voids (four shown here). Voids + soft rubber = high compliance (“mushy”) under transient loads.

Design approach

Instead of installing another rubber bushing, the goal was to keep the original metal shell and center sleeve (pin), but replace the compliant rubber with a much stiffer casting polyurethane. A Shore 90A polyurethane is substantially harder than typical OEM rubber used in the OEM mounts, and (when fully cured) behaves more like a high-durometer industrial elastomer than a soft “rubber mount.”

PMC 770, 780, and 790 product information
Product reference: PMC 770/780/790 family description. In this project I used PMC-790 (Shore 90A), chosen specifically for stiffness and durability.
Notes on “PMC 90 polyurethane” terminology

“PMC 90” is often used as shorthand for a ~Shore 90A polyurethane (for example PMC-790) used in industrial/mechanical applications where high tear strength and abrasion resistance are desired. In automotive contexts, “90A” generally indicates a very firm bushing compared to typical rubber NVH bushings.

Step-by-step process with photos

Inside of bushing after drilling out rubber
Photo 2: Inside the bushing after drilling out most of the rubber.
Chiseling out remaining rubber from bushing shell
Photo 3: Chiseling out the remaining rubber and separating it from the shell.
Metal shell cleaned out with rubber removed
Photo 4: What remains once the rubber is removed: the reusable metal shell and components.
Center sleeve scored to improve polyurethane grip
Photo 5: Scoring the center sleeve (pin) to create mechanical “keying” so the cured polyurethane has more bite than a smooth surface provides.
Measuring to ensure the sleeve is centered
Photo 6: Measuring to ensure the center sleeve is accurately centered before the pour.
Setup/jig to hold arm and bushing for the pour
Photo 7: Pour setup. The arm/bushing is fixtured so the shell is stable and the sleeve stays centered while the polyurethane cures.
Final cured polyurethane bushing installed in shell
Photo 8: After curing: the bushing is filled with the new polyurethane and retains the original shell geometry.
Close-up of final cured bushing
Photo 9: Close-up of the finished bushing.

Process notes (practical details)

Results

With the stiffer 90A polyurethane bushing installed, the drivetrain no longer “winds up” and rebounds during quick throttle lift or during shift transitions. Engine/transmission fore–aft motion is significantly reduced, and shifting is easier because the drivetrain stays better located instead of moving around between clutch events.

In practical driving terms: less lurch, less rocking, more predictable engagement.