Adding a Second External Cooler to the Rialta

Theory

This write-up applies to folks who currently have a external cooler mounted in the front of their Rialta. Although the current external cooler upgrade is sufficient for most driving conditions it seems that given what I have read on the web, observed on my own Rialta and also from reading the forum posts, that under more extreme coditions, the external cooler upgrade may not be enough. Specifically this can happen when stuck in traffic on a very hot day or when climbing long hills in hot weather. The solution suggested by the Rialta forum experts when stuck in traffic with the current external cooler is to turn on the air conditioner in the cab which forces the engine fans on. Doing this causes more air flow through the external cooler mounted in front of the condenser and engine radiator. This is also the same suggeston when climbing hills. I believe that these are good ideas and work well in most cases.

Plan

From what I have read on the forum, some people have experienced situations where this approach might not be enough and the temperature of the transmission can get so high that they find it necessary to pull over to allow the transmission to cool off.
After doing a bit of reseach I found that some truckers and off roaders have the same problem and solve this problem by installing an additional fan driven remote cooler in series with their existing remote cooler. They either flip a manual switch or use a thermostat to turn their second remote external fan driven cooler on to keep the transmission temperatures down.
Leaving the current external cooler mounted in front of the condenser in place and installing a additional fan driven cooler has the benefit of extra cooling and also, should the fan driven cooler fan stop working one still has the cooling of the other cooler.

(For purposes of discussion, Let's call the current external cooler, cooler1 and the new external fan driven cooler cooler2.)

The idea is to route the current transmission cooler hoses to allow the fluid to flow through both coolers (in series). .


The original plan was to use a thermostat I purchased with cooler2 which was supposed to go on when the temperature of the fluid coming out of the transmission was 180 degrees. Two things I believe made this not work well. The first was that the thermostat switch did not really go on at 180 degress but it had to get to 187 degrees (tested on stove with hot water and digital thermometer). The second was that as the fluid leaves the transmission and travels to external cooler2 it cooled a little so that the switch was not activating even when the scangauge said the transmission temps were in the high 190's.


Because of this I decided instead to not use a thermostat and to just add a switch to the dashboard where I could manually turn on cooler2 when needed.

If you decide to not use a thermostat you can route the transmission hoses in a little different configuration. The back banjo bolt and fitting on the transmission is where the hot fluid pumps out of the transmission and I wanted that hot fluid to go right to the thermostat. When not using a thermostat this does not matter anymore so the closest banjo bolt to the front of the RV can be pointed to the back instead of the furthest banjo bolt. This makes it easier to connect the hoses to the current banjo bolt fittings.

(I bought new banjo bolt seals at VW for the banjo bolt I turned around to face the back of the RV. It may not have been necessary but I did it anyway.

As for the additional cooler, this is the one I selected. I had 2 criteria for picking this additional cooler, first it had to fit under the Rialta and second it had to be a 'large' cooler in terms of it's ability to cool. At 67,000 BTU it seemed quite 'large' although I don't know what the equivalent rating this is to GVWR.





This cooler fits perfectly under the Rialta just behind the gas tank on the drivers side. The location I chose had a canister for the EVAP control system in the way so I moved the canister to a new location with a longer hose.



To mount it so that the unit is tucked away under the RV but has enough airflow I bought a pice of metal from the hardware store and cut it to 4 pieces which I bent on a vice as shown.





Make holes under RV support a little larger to the hoses can be connected to the cooler.



Slip cooler into space and attach from below with self taping metal screws.



You also need barbed fittings to fit into the cooler which I had to purchase separately.



Here is the hose I used, replacing the existing hoses so all the hoses would be new. If you reuse some of the existing hose that goes to your current external cooler you won't need as much.





For routing the hoses you can follow where the 2 current rear engine coolant hoses go up over the gas tank. It is a little hard to push them through but there is enough room and they do fit. You also need to run a single wire from a switch mounted on your dash that supplies 12volts to the cooler. The wire needs to be able to carry at least 10 amps (16 gauge) because the cooler uses around 9 amps. I used 14 gauge just to be safe. I routed this along with the hoses and protected it as it ran over the gas tank by putting it through a section of soft clear tubing. ( It also makes it easier to get the wire up and over the tank when it is in the tubing)


And lastly you need to wire up and power a switch to connect to the wire from the cooler. Ideally it would be best to have this wire connected to the circuit that is only energized when the key is on but since I couldn't figure out which relay would be best to tap into for this I just connected the power to the cab battery with an inline 10 amp fuse.



The switch on the dash is a lighted switch so I can visually see that the cooler has been turned on. If you turn off the engine to get out of the RV you not only see that the light is on the switch but when you get out of the vehicle you can clearly hear the cooler fan running so you know to shut it off. For now, I am going to leave it that way and maybe some day tap into the circuit that powers off when the key is turned off.



I hope this writeup is helpful for anyone who is going to do this modification.