Manual Transmission Swap VR6 Eurovan/Rialta

Ed Tornick

This document applies to 12 and 24 valve VR6 engines in the Rialta motorhome(which is built on the eurovan chasis).

To take out the 4 speed 01P automatic transmission from the Rialta and replace it with a manual transmission you first need to find a 02G AFL 5 speed manual transmission and ancillary parts from the donor vehicle. A 'swap kit' can be purchased from Quality German Auto Parts in Victorville CA. I bought one and it came with everything I needed to do the conversion.
A major stumbling block with this conversion is that the automatic transmission controller (TCM) will be quite upset when it realizes that there is no automatic transmission attached to it.
This will cause the Check Engine Light (CEL) to go on.
Dean segovis at Hack A Week came up with a solution in the form of a hardware hack. The TCM and it’s wire harness that used to connect to the transmission must stay installed in the vehicle. Dean created a small device (Transmission Emulator) that made up of the same solenoids and ribbon cable that is inside the transmission. Three cables from the TCM plug into the emulator and a 4th cable has a jumper plug. This fools the TCM into thinking that the automatic transmission is there and it is in Drive.


Picking up the transmission I ordered from Quality German Auto Parts in Victorville CA The transmission was shipped to a shipping company located near me.





The box contained

The transmission before cleaning up.



I opted for a new flywheel, clutch and throwout bearing. After it was installed the master clutch cylinder failed and the pedal went to the floor so I suggest getting a new one of those as well. I was able to find one at FCP euro in Milford CT.

The pedal assembly came as a large unit with the brake master cylinder and brake booster attached. All that is needed from this unit is the clutch pedal, a few pedal springs, the clutch master cylinder and the large pin that goes through all the pedals.







There is a port on the brake master cylinder that a hose needs to be connected to that will now go to the clutch master cylinder. Part of the end needs to be clipped off and it is ready for the hose.





The engine is suspended by a hanger support bar that I borrowed from a mechanic friend. They sell these on Harbor Freight for under $100. Alternatively one could possibly just mount a 4x4 across the front to hold the engine up. The chain is then attached to a tool I made by copying what I found in the Bentley manual.





Before removing the CV axles make sure to back off the torsion bar nuts on both sides. Measure the distance from the nut to the end of the bolt before loosening them so you can return them to the original position when the job is done. To pull the CV axle on the Drivers (left) side you really need to push up on the control arm in order to get the axle out. It comes off the transmission easily but hits part of the frame unless the control arm is pushed up out of the way.





Automatic transmission (01P) is out.





Thought it would be a good idea to replace the 3 transmission axle seals. The axial shaft (input shaft) seal looked quite old and brittle. After a bit of research determined the size of the axial shaft seal and the 2 cv axle seals. I found a company that makes seals of the needed size and replaced them. The driver and passenger side axle shaft seals the same size.



First remove the axle shafts to get at the axle shaft seals

Driver side is easy



Passenger side a bit more complicated



Replace the smaller input shaft seal







This part is called the stub axle shaft. It is connected to the engine with a bracket on the passenger side and it's purpose is to extend the axle shaft on the transmission so that the cv axles are the same length. Without this the distance from the hub on the passenger side to the axle shaft on the transmission would require a much longer CV axle on the passenger side. This "stub axle shaft" bearing was dry. Pressed out the old one and pressed on a new one I found on ebay.





The automatic transmission CV axles in my Rialta fit perfectly with the manual transmission. According to some AI research I did

For the typical 1997-2003 VR6 or 2.5 TDI Eurovan/T4 doing the 01P→02G swap the original automatic axles and stub shaft bolt straight onto the manual. Just confirm the bolt pattern and make sure the stub shaft is present and healthy; that’s all most swappers need to worry about.



There were 2 outstanding issues that still needed to be resolved before everything can be operational.

1. The park/neutral position relay under the center of the dash gets its automatic shifter position via the multifunction switch on the transmission. Since the Transmission emulator jumper plug is set to the Drive position permanently relay (175) will not allow the starter to get power.

2. Getting the reverse lights to work (and backup camera) when the manual transmission is shifted into reverse. Deans Suggested solution to the Park/Neutral and reverse lights issue

I decided to tackle the engine start issue differently but used his reverse light solution. For the park/neutral relay starting issue, instead of modifying the Park/Neutral relay I added a simple circuit that energizes the starter solenoid directly from the battery (with 15 amp fuse) with a dash mounted button. The sequence to start the vehicle is put the ignition key in the run position, then push the start button. Since the transmission emulator is hard wired to Drive the engine starts right up.



The only problem with this solution is that the alternator has a connector that needs 12 volts applied to it momentarily to get it to start charging. (called the exciter). In normal unmodified operation, when the ignition switch is rotated into the start position 12 volts is applied to this exciter wire.
Since this solution starts the vehicle without turning the ignition key to start, I used a simple 12 volt relay that is energized by voltage being applied to the starter solenoid. When the starter is activated (pushing the dash mounted start button) 12 volts is applied to the exciter via the connected relay contacts Start schematic.

The alternative option to using the relay is with one hand hold the key in the start positon and with the other push the start button. An advantage of this is it might make the RV more difficult to steal and requires no relay and extra wiring, just a push button that sends 12 volts to the starter solenoid.

Final Thoughts





So far am very happy with the results of the swap. I kept the scan gauge on the dash even though there is no need to monitor transmission temperature anymore. It seems good to have for other monitoring and general code interpretation in case any pop up.